We are proud to announce the launch of SciCan OPTIM OS1 Liquid to round out our new line of OPTIM OS1 broad-spectrum, hospital-grade cleaner-disinfectant products.
OPTIM OS1 is a one-step, cleaner-disinfectant that removes soil and hard-to-kill organisms from clinical contact surfaces. It’s proprietary LAS Active System formulation kills bacteria, viruses, TB bacteria, and emerging pathogens in just 1 minute.
Rapid contact times for best results
- 60-second kill times for viruses, bacteria, and yeast
- Kills TB Bacteria in only 45 seconds and Candida auris in 60 seconds
Safe for use on hard, non-porous clinical surfaces
- Cleans and disinfects stainless steel, anodized aluminum, non-porous upholstery, Corian countertops, silicone, and more
Formulated with the user in mind
- VOC-free, fragrance-free and dye-free
Emerging Pathogen Claim ensures your clinic is ready for the next viral
threat
- Qualifies for EPA’s Emerging Viral Pathogen Claim
- Kills SARS-CoV-2, the virus that causes COVID-19, in only 30 seconds
You can learn more about OPTIM’s newest formula below
OPTIM OS1 Wipes Quick Reference Guide
Consult the product label before using this surface disinfectant.
OPTIM OS1 SOLUTION Liquid Spray
Spray Ready-to-Use OPTIM OS1 liquid onto a SciCan Dry Towelette. Do not directly spray onto the surface.
If surface is not heavily soiled, clean and disinfect surface with one wipe and allow surface to remain wet for the contact time indicated on the label.
If surface is visibly soiled, clean surface with one
towelette and discard. Use a second towelette to disinfect and allow surface to remain wet for the contact time indicated on the label.
OPTIM OS1 Ready-to-Use Wipes
Pull out OPTIM OS1 towelette at a 45 degree angle. Close lid.
If surface is not heavily soiled, clean and disinfect surface with one wipe and allow surface to remain wet for the contact time indicated on the label.
If surface is visibly soiled, clean surface with one towelette and discard. Use a second towelette to disinfect and allow surface to remain wet for the contact time indicated on the label.
IMPORTANT !
DO NOT allow OPTIM OS1 to pool on surfaces.
Use of gauze dipped in solutions for wiping may cause pooling and should be wiped dry.
FOR BEST RESULTS:
- Do not over apply OPTIM OS1
- Use of OPTIM OS1 on brass, copper, and clear acrylic could discolor or damage surfaces, if not used as directed and over applied.
- Dental Association guidelines recommend the use of utility gloves when cleaning and disinfecting surfaces.
PLEASE REFER TO THE ORIGINAL CONTAINER FOR COMPLETE DIRECTIONS AND ADDITIONAL INFORMATION.
Procedure for disinfecting PVS elastomeric impression materials with OPTIM OS1
- Once the impression is taken, rinse it well under running tap water to remove blood and saliva.
- After rinsing, gently shake the impression within the sink basin to remove any adherent water with minimal splatter.
- Spray the entire impression with OPTIM OS1. Use the contact times as stated on the label.
- Rinse the impression thoroughly with tap water to remove any excess disinfectant. After a thorough rinse, gently
shake the impression inside the sink basin to remove any adherent water with minimal splatter. - Once dry, place the disinfected impression in a sealed bag.
The impression is now safe and ready for further processing.
Switching to OPTIM OS1
- Give all surfaces a good cleaning with soap and water before switching to OPTIM OS1.
- After switching to OPTIM OS1, surfaces should to be periodically rinsed with water (recommended no less than once per week).
- Common practice for all chemical disinfectants is to periodically rinse and dry surfaces to maintain the surface integrity.
- Avoid mixing of chemistries.
Your Steri-Center’s best friend.
VistaPure™ provides two grades of high-quality water for autoclaves, dental bottles,
ultrasonic cleaners and instrument washers for the ultimate convenience.
Features
Universal System
VistaPure will work with the STATIM® Cassette Autoclaves, BRAVO™ Chamber Autoclaves, HYDRIM® Instrument Washers, Ultrasonic Cleaners, Dental Bottles, other select sterilizers and automated washers.
High Quality Water
Water is autoclave-ready, distilled quality (deionized) water which eliminates the need to buy distilled water or own a distiller.
Easy to Use
VistaPure’s handheld, point-and-shoot wand makes it easy for anyone to fill autoclaves, no matter where they’re located, and the system’s mounted faucet makes it easy to fill Dental Unit bottles over a sink. We will also offer unique “automatic water filling control” options for our STATIM and BRAVO sterilizers along with our HYDRIM final rinse options.
Smart Design
VistaPure’s filter panel fits neatly under the steri-center counter with slides for easy access to the filters.
Convenient
VistaPure provides a high volume of ready-to-use water, on demand. Its large 4.25-gallon storage tank means you don’t need to wait for deionization and R/O processes to take place.
Consistent
Each VistaPure features an in-line TDS meter that monitors water quality—and also makes it easy to know when it’s time to replace your filters.
Hands Free
VistaPure accessories include patented AutoFill devices designed to replenish SciCan STATIM and BRAVO autoclaves with distilled-quality water automatically, enabling truly hands-free convenience. An optional adapter kit is also available for utilizing VistaPure’s hyper-filtered water for the final rinse cycle of instrument washers.
Articles
VistaPure Water Filtration System Two grades of high-quality water for all practice sterilization needs
Inside Dentistry, Feb 2016
VistaPure AutoFill
VistaPure’s patented AutoFill accessories replenish SciCan STATIM®and BRAVO™ autoclaves with distilled-quality water automatically — enabling truly hands-free convenience.
VistaPure AutoFill accessory kits work with all VistaPure systems and can be installed easily on any STATIM 2000/G4 or STATIM 5000/G4, or any BRAVO autoclave, in just a few minutes!
- No more purchasing and storing distilled water
- No more cycle-fault errors caused by forgetting to fill reservoirs
- No more spills while filling autoclaves manually
- No more staff time spent filling autoclaves = more time with patients
VistaPure AutoFill Installation
A 12-foot length of clear polyurethane tubing is already attached to the AutoFill manifold. If the desired distance between the connection to the VistaPure and the autoclave is greater than 12 feet, simply order a longer length of the clear polyurethane tubing, as the distance from the VistaPure to the autoclave is not limited, except by the feed tubing.
Installing AutoFill on a STATIM
The VistaPure AutoFill for STATIM device (S3020) can be installed on any STATIM 2000/G4 or STATIM 5000/G4 autoclave as follows:
Installing AutoFill on a BRAVO
The VistaPure AutoFill for BRAVO device (S3030) can be installed on any model BRAVO autoclave.
In order to connect the VistaPure AutoFill to the BRAVO, one of the two tanks that come with the BRAVO must be selected as a “relay tank” since the BRAVO system uses a suction-lift pump to fill its reservoir when in its automatic-filling mode. Note that the relay tank must be located within 6 feet of the BRAVO unit, due to the suction-lift capacity of the BRAVO pump.
Connecting to a StatClave G4
![AquaStat Distiller [Replaced by LP90, LP80, DP860 or VistaPure]](https://i0.wp.com/d2j6dbq0eux0bg.cloudfront.net/images/226067/469791773.jpg?resize=238%2C400&quality=89&ssl=1 "AquaStat Distiller [Replaced by LP90, LP80, DP860 or VistaPure]")
