We are proud to announce the launch of SciCan OPTIM OS1 Liquid to round out our new line of OPTIM OS1 broad-spectrum, hospital-grade cleaner-disinfectant products.
OPTIM OS1 is a one-step, cleaner-disinfectant that removes soil and hard-to-kill organisms from clinical contact surfaces. It’s proprietary LAS Active System formulation kills bacteria, viruses, TB bacteria, and emerging pathogens in just 1 minute.
Rapid contact times for best results
- 60-second kill times for viruses, bacteria, and yeast
- Kills TB Bacteria in only 45 seconds and Candida auris in 60 seconds
Safe for use on hard, non-porous clinical surfaces
- Cleans and disinfects stainless steel, anodized aluminum, non-porous upholstery, Corian countertops, silicone, and more
Formulated with the user in mind
- VOC-free, fragrance-free and dye-free
Emerging Pathogen Claim ensures your clinic is ready for the next viral
threat
- Qualifies for EPA’s Emerging Viral Pathogen Claim
- Kills SARS-CoV-2, the virus that causes COVID-19, in only 30 seconds
You can learn more about OPTIM’s newest formula below
OPTIM OS1 Wipes Quick Reference Guide
Consult the product label before using this surface disinfectant.
OPTIM OS1 SOLUTION Liquid Spray
Spray Ready-to-Use OPTIM OS1 liquid onto a SciCan Dry Towelette. Do not directly spray onto the surface.
If surface is not heavily soiled, clean and disinfect surface with one wipe and allow surface to remain wet for the contact time indicated on the label.
If surface is visibly soiled, clean surface with one
towelette and discard. Use a second towelette to disinfect and allow surface to remain wet for the contact time indicated on the label.
OPTIM OS1 Ready-to-Use Wipes
Pull out OPTIM OS1 towelette at a 45 degree angle. Close lid.
If surface is not heavily soiled, clean and disinfect surface with one wipe and allow surface to remain wet for the contact time indicated on the label.
If surface is visibly soiled, clean surface with one towelette and discard. Use a second towelette to disinfect and allow surface to remain wet for the contact time indicated on the label.
IMPORTANT !
DO NOT allow OPTIM OS1 to pool on surfaces.
Use of gauze dipped in solutions for wiping may cause pooling and should be wiped dry.
FOR BEST RESULTS:
- Do not over apply OPTIM OS1
- Use of OPTIM OS1 on brass, copper, and clear acrylic could discolor or damage surfaces, if not used as directed and over applied.
- Dental Association guidelines recommend the use of utility gloves when cleaning and disinfecting surfaces.
PLEASE REFER TO THE ORIGINAL CONTAINER FOR COMPLETE DIRECTIONS AND ADDITIONAL INFORMATION.
Procedure for disinfecting PVS elastomeric impression materials with OPTIM OS1
- Once the impression is taken, rinse it well under running tap water to remove blood and saliva.
- After rinsing, gently shake the impression within the sink basin to remove any adherent water with minimal splatter.
- Spray the entire impression with OPTIM OS1. Use the contact times as stated on the label.
- Rinse the impression thoroughly with tap water to remove any excess disinfectant. After a thorough rinse, gently
shake the impression inside the sink basin to remove any adherent water with minimal splatter. - Once dry, place the disinfected impression in a sealed bag.
The impression is now safe and ready for further processing.
Switching to OPTIM OS1
- Give all surfaces a good cleaning with soap and water before switching to OPTIM OS1.
- After switching to OPTIM OS1, surfaces should to be periodically rinsed with water (recommended no less than once per week).
- Common practice for all chemical disinfectants is to periodically rinse and dry surfaces to maintain the surface integrity.
- Avoid mixing of chemistries.
STATPURE Water Filtration System
Simplified water filtration and easy maintenance to match your workflow.
STATPURE’s unique four-filter configuration produces exceptional quality water for autoclaves while also making hyper-filtered RO water for dental bottles, ultrasonic cleaners, and final rinsing in automated instrument washers.
The streamlined design neatly organizes tubing for easy, intuitive installation, while QuickTwist filters cut maintenance time down to moments.
MORE TIME
STATPURE eliminates storing and handling heavy bottled water. Its simple design cuts filter change times in half, and it can be configured to autofill SciCan reprocessing equipment.
MORE SAVINGS
STATPURE lowers your clinic’s costs long-term by eliminating bottled water purchases. Its four‑filter system produces high‑purity water without extra filters.
MORE WATER
Powered by your municipal water supply, STATPURE delivers a high volume of on demand water. Match your clinic’s needs with the 4.25-gallon or 9.5-gallon net storage tanks to keep your instrument reprocessing moving.
MORE PROTECTION
STATPURE is backed by a 2-year warranty that protects your investment and provides confidence you can rely on dependable water filtration for your stericenter workflow.
Autoclave Fill Wand
The wand’s grip-pressure control reduces hand strain, making daily autoclave filling easier and faster for your busy practice.
*Actual filter lifespan depends on local water quality, inbound water pressure, and volume of water used. Filter replacement intervals will be based on TDS readings.
Installation Space Requirements
4.25 Gallon (16 L) Water Storage Tank
STANDARD
Height 17.75”/ 45.08 cm
9.5 Gallon (36 L) Water Storage Tank
OPTIONAL
Height 22” / 55.88 cm
Filter Kits & Accessories
STATPURE Filter Kit 1
(Prefilter & Polishing)
STATPURE Filter Kit 2
(DI 2-Pack)
STATPURE Multipack Kit 3
(1 x Pre, 2 x DI, 1 x Pol)
Auxiliary EV Kit
for BRAVO G4
